Search results

• Manual:Fast Path
  For fast path to work, interface support and specific configuration conditions are required. Interface FastPath support can be checked by doing "/interface print detail" and seeing fast-path property value.
  5 KB (628 words) - 15:31, 14 December 2015
• Manual:TE Tunnels Example
  /interface bridge add name=lo0 add address=192.168.55.1/30 interface=ether1
  7 KB (723 words) - 14:37, 14 December 2015
• Manual:Interface/EoIP
  <p id="shbox"><b>Sub-menu:</b> <code>/interface eoip</code> ...tion. The EoIP tunnel may run over [[M:Interface/IPIP | IPIP]] tunnel, [[M:Interface/PPTP | PPTP]] tunnel or any other connection capable of transporting IP. <b
  9 KB (1,340 words) - 17:51, 26 August 2015
• Manual:Interface/VPLS
  ...e can be considered tunnel interface just like [[M:Interface/EoIP | EoIP]] interface. To achieve transparent ethernet segment forwarding between customer sites. <p id="shbox"><b>Sub-menu:</b> <code>/interface vpls</code></p>
  10 KB (1,293 words) - 11:40, 26 January 2015
• Manual:MPLS over PPPoE
  ...be able to forward 1500 byte IP packet without fragmentation we will need interface that supports <br /> ...ed to ether2. From the table you can see that max supported l2MTU for this interface is 1522.
  7 KB (840 words) - 18:22, 26 August 2015
• Manual:IP/Hotspot/User
  |desc=Allows to add mac cookie for users. [[M:Hotspot_Introduction#MAC_Cookie |<code>Read more>></code>]] |desc=Selects mac-cookie timeout from last login or logout. [[M:Hotspot_Introduction#MAC_Cookie |<code>Read more>></code>]]
  9 KB (1,223 words) - 12:25, 29 January 2015
• Manual:BGP Load Balancing with two interfaces
  ...e''' configuration setting is used to bind the BGP connection to the right interface. # loopback interface
  6 KB (734 words) - 13:17, 10 December 2015
• Manual:Layer-3 MPLS VPN example
  /ip address add address=10.1.1.2/24 interface=ether2 /ip address add address=10.2.2.2/24 interface=ether3
  9 KB (1,012 words) - 15:35, 14 December 2015
• Manual:EBGP as PE-CE routing protocol
  ip address add address=10.1.1.1/30 interface=A_B; ip address add address=10.1.1.5/30 interface=A_C;
  13 KB (1,597 words) - 14:33, 14 December 2015
• Manual:RouterOS6 news
  ...ry on interface you now must use command: "'''/ip neighbor discovery set (interface number/name) discover=yes/no'''". * Slave flag shows up for interfaces that are in bridge,bonding or switch group;
  6 KB (874 words) - 09:53, 26 January 2015
• Manual:Interface/W60G
  ==General interface properties== <b>Sub-menu:</b> <code>/interface w60g</code>
  14 KB (1,881 words) - 18:31, 25 March 2019
• Manual:Spanning Tree Protocol
  ...network, then leaving STP settings to automatic may elect a undesired root bridge and root ports and in case of a hardware failure can result in an inaccessi You can check the STP status of a bridge by using the <code>/interface bridge monitor</code> command, for example:
  33 KB (5,318 words) - 17:27, 8 May 2018
• Manual:Metarouter
  ...ou need to add a new interface to your virtual router. This is done in the interface menu. The interface command has the following options:
  18 KB (2,434 words) - 15:29, 14 December 2015
• Manual:IPv6/Address
  ...hat IPv6 automatically generates a link-local IPv6 address for each active interface that has IPv6 support. Packets addressed to a unicast address are delivered only to a single interface. To this group belong:
  16 KB (2,302 words) - 18:09, 29 January 2015
• Manual:Simple TE
  /interface bridge add name=Loopback add address=192.168.33.1/30 interface=ether1
  12 KB (1,423 words) - 13:42, 14 December 2015
• Manual:OSPF-examples
  [admin@CableFreeR1]/ip address add address=10.10.1.1/30 interface=ether1 [admin@CableFreeR1]/ip address add address=10.10.1.5/30 interface=ether2
  12 KB (1,566 words) - 19:11, 29 January 2015
• Manual:IP/Firewall/Filter
  <li> interface the packet arrived from or left through [[M:Packet_Flow | Packet flow]] diagrams illustrate how packets are processed i
  27 KB (4,147 words) - 12:02, 29 January 2015
• Manual:PPP AAA
  ...nual:Interface/PPPoE | PPPoE]], [[Manual:Interface/PPTP | PPTP]], [[Manual:Interface/L2TP | L2TP]] and ISDN connections. The attributes received from RADIUS ser |arg=bridge
  16 KB (2,373 words) - 16:54, 26 August 2015
• Manual:IP/DHCP Server
  The router supports an individual server for each Ethernet-like interface. The CableFree RadioOS DHCP server supports the basic functions of giving e ...x-rate-min]]]]. All rates should be numbers with optional 'k' (1,000s) or 'M' (1,000,000s). If tx-rate is not specified, rx-rate is as tx-rate too. Same
  24 KB (3,820 words) - 17:14, 30 April 2015
• Manual:Webfig
  ...nfigure and troubleshoot the router. It is designed as an alternative of [[M:Winbox | WinBox]], both have similar layouts and both have access to almost * Monitoring - display the current status of the router, routing information, interface stats, logs and many more;
  9 KB (1,524 words) - 19:53, 1 June 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)