Search results

• User Manager/Customer page
  ...Check the box on the right to show [[User Manager/Limiting #Rate limits | rate limit]] field group; There are groups of fields (for example, private information, rate limits). These fields are hidden by default and are accessible by checking
  11 KB (1,514 words) - 17:53, 10 May 2016
• Manual:Queue
  * limit data rate for certain IP addresses, subnets, protocols, ports, and other parameters ==Rate limitation principles==
  27 KB (3,883 words) - 10:16, 24 November 2015
• IPSEC between CableFree router and a Shrew client
  n:network-natt-rate:15 add chain=input connection-state=established
  9 KB (1,178 words) - 12:42, 29 January 2015
• Manual:RadioOS features
  <li>Internal connection, routing and packet marks <li>[[Manual:PCC | PCC]] - per connection classifier, used in load balancing configurations
  6 KB (932 words) - 10:41, 26 July 2016
• Manual:TOC
  * [[Manual:Connection_oriented_communication_(TCP/IP) | Connection Oriented Communication (TCP/IP)]] * [[Manual:Connection_oriented_communication_(TCP/IP) | Connection Oriented Communication (TCP/IP)]]
  17 KB (1,912 words) - 15:20, 22 February 2017
• NV2
  Nv2 implements dynamic rate selection on per-client basis and ARQ for data transmissions. This enables ...the size of contention time slot that AP allocates for clients to initiate connection and also size of time slots used for estimating distance to client. If this
  15 KB (2,370 words) - 17:07, 26 January 2015
• Manual:Nv2
  Nv2 implements dynamic rate selection on per-client basis and ARQ for data transmissions. This enables ...the size of contention time slot that AP allocates for clients to initiate connection and also size of time slots used for estimating distance to client. If this
  15 KB (2,389 words) - 17:36, 26 August 2015
• Manual:Interface/Bonding
  ...e 2 NICs in each router (Router1 and Router2) and want to get maximum data rate between 2 routers. To make this possible, follow these steps: /inteface bonding add slaves=ether1,ether2 mode=802.3ad lacp-rate=30secs link-monitoring=mii-type1 \
  21 KB (3,226 words) - 15:41, 26 January 2015
• Manual:TE Tunnels
  ...ed over link as well) or more (in case data is forwarded over tunnels with rate smaller than allocated for tunnel) than bandwidth available for reservation ...o establish IP VPN between his 3 sites and Customer B wants to transparent connection for ethernet segments at his sites.
  13 KB (1,780 words) - 18:29, 26 August 2015
• Manual:Interface/LTE
  Add new connection parameters under LTE apn profile (provided by network provider): Select newly created profile for LTE connection:
  14 KB (2,062 words) - 09:43, 24 April 2018
• Manual:Interface/Wireless
  This property has effect only in AP modes, and when value of '''rate-set''' is configured. ...t this point 3 * ('''hw-retries''' + 1) frame transmits on the lowest data rate had failed.
  97 KB (13,432 words) - 19:48, 16 December 2016
• Manual:Interface/PPPoE
  ...ressed in transport method: PPPoE employs Ethernet instead of serial modem connection. ...us extra 10KiB for packet queue, if data rate limitation is used) for each connection) and CPU power. Maximum of 65535 connections is supported.
  30 KB (4,611 words) - 16:16, 26 August 2015
• Manual:Tools/Traffic Generator
  ...NUM TX-PACKET TX-RATE RX-PACKET RX-RATE LOST-PACKET LOST-RATE ...Q PORT RX-UNK-PACKET RX-UNK-BYTE RX-UNK... TX-PACKET TX-RATE RX-PACKET
  28 KB (2,616 words) - 18:42, 26 August 2015
• Manual:CAPSMAN
  ...only requires the minimum configuration required to allow it to establish connection with CAPSMAN. Functions that were conventionally executed by an AP (like ac * improved CAP<->CAPSMAN data connection protocol
  41 KB (5,870 words) - 17:08, 30 April 2015
• Manual:Interface/Bridge
  ...ridged (depending on the way the LANs are interconnected, latency and data rate between hosts may vary). ...oops, are put to standby, so that should the main connection fail, another connection could take its place. This algorithm exchanges configuration messages (BPD
  47 KB (7,052 words) - 17:52, 8 May 2018
• Manual:Troubleshooting tools
  Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mshome.net
  18 KB (2,376 words) - 10:59, 29 January 2015
• Manual:IP/IPsec
  ...y SAs. The policy notifies IKE daemon about that, and IKE daemon initiates connection to remote host. IKE daemon responds to remote connection.
  47 KB (6,594 words) - 12:38, 29 January 2015
• Manual:Interface/HWMPplus
  ...Distribution System interface. Remote MAC address is learnt from wireless connection data * <var>wireless</var> - Remote MAC addresses are learnt from wireless connection data
  23 KB (3,557 words) - 17:42, 26 August 2015
• Manual:Metarouter
  [Q - quit connection] [B - send break] [A - send Ctrl-A prefix] [R - autoconfigure rate]
  18 KB (2,434 words) - 15:29, 14 December 2015
• Manual:KVM
  [Q - quit connection] [B - send break] [A - send Ctrl-A prefix] [R - autoconfigure rate]
  24 KB (3,443 words) - 16:11, 14 December 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)