Search results

For fast path to work, interface support and specific configuration conditions are required. Interface FastPath support can be checked by doing "/interface print detail" and seeing fast-path property value.

/interface bridge add name=lo0 add address=192.168.55.1/30 interface=ether1

<p id="shbox"><b>Sub-menu:</b> <code>/interface eoip</code> ...tion. The EoIP tunnel may run over [[M:Interface/IPIP | IPIP]] tunnel, [[M:Interface/PPTP | PPTP]] tunnel or any other connection capable of transporting IP. <b

...e can be considered tunnel interface just like [[M:Interface/EoIP | EoIP]] interface. To achieve transparent ethernet segment forwarding between customer sites. <p id="shbox"><b>Sub-menu:</b> <code>/interface vpls</code></p>

...be able to forward 1500 byte IP packet without fragmentation we will need interface that supports <br /> ...ed to ether2. From the table you can see that max supported l2MTU for this interface is 1522.

|desc=Allows to add mac cookie for users. [[M:Hotspot_Introduction#MAC_Cookie |<code>Read more>></code>]] |desc=Selects mac-cookie timeout from last login or logout. [[M:Hotspot_Introduction#MAC_Cookie |<code>Read more>></code>]]

...e''' configuration setting is used to bind the BGP connection to the right interface. # loopback interface

/ip address add address=10.1.1.2/24 interface=ether2 /ip address add address=10.2.2.2/24 interface=ether3

ip address add address=10.1.1.1/30 interface=A_B; ip address add address=10.1.1.5/30 interface=A_C;

...ry on interface you now must use command: "'''/ip neighbor discovery set (interface number/name) discover=yes/no'''". * Slave flag shows up for interfaces that are in bridge,bonding or switch group;

==General interface properties== <b>Sub-menu:</b> <code>/interface w60g</code>

...network, then leaving STP settings to automatic may elect a undesired root bridge and root ports and in case of a hardware failure can result in an inaccessi You can check the STP status of a bridge by using the <code>/interface bridge monitor</code> command, for example:

...ou need to add a new interface to your virtual router. This is done in the interface menu. The interface command has the following options:

...hat IPv6 automatically generates a link-local IPv6 address for each active interface that has IPv6 support. Packets addressed to a unicast address are delivered only to a single interface. To this group belong:

/interface bridge add name=Loopback add address=192.168.33.1/30 interface=ether1

[admin@CableFreeR1]/ip address add address=10.10.1.1/30 interface=ether1 [admin@CableFreeR1]/ip address add address=10.10.1.5/30 interface=ether2

<li> interface the packet arrived from or left through [[M:Packet_Flow | Packet flow]] diagrams illustrate how packets are processed i

...nual:Interface/PPPoE | PPPoE]], [[Manual:Interface/PPTP | PPTP]], [[Manual:Interface/L2TP | L2TP]] and ISDN connections. The attributes received from RADIUS ser |arg=bridge

The router supports an individual server for each Ethernet-like interface. The CableFree RadioOS DHCP server supports the basic functions of giving e ...x-rate-min]]]]. All rates should be numbers with optional 'k' (1,000s) or 'M' (1,000,000s). If tx-rate is not specified, rx-rate is as tx-rate too. Same

...nfigure and troubleshoot the router. It is designed as an alternative of [[M:Winbox | WinBox]], both have similar layouts and both have access to almost * Monitoring - display the current status of the router, routing information, interface stats, logs and many more;

{{ Note | ''When a DHCP-Relay server is attached to an interface in a vrf, the communications from that DHCP-Relay to the remote DHCP-Server /ip address add address=10.1.1.1/24 interface=ether1

...PLS network with "loopback" IP addresses (not attached to any real network interface) to be used by LDP to establish sessions. ...nect them, loopback IP address ensures that LDP session is not affected by interface state or address changes

...of the configuration is on the back of the box and also described in the [[M:Default_Configurations | online manual]]. Initial configuration has DHCP client on WAN interface (ether1), rest of the ports are considered your local network with DHCP ser

[admin@CAP] > /interface wireless cap set lock-to-caps-man=yes [admin@wtp] > /interface wireless cap print

...e data forwarding (either by bridging or routing) to/from virtual-ethernet interface in host system, guest VM can be allowed to participate in real network. ...hat will appear in guest VM as ethernet interfaces are configured in "/xen interface" menu:

...fferent routing table based on destination address, source address, source interface, and routing mark (can be changed by firewall mangle rules) of the packet. ...re created automatically for each IP network that has at least one enabled interface attached to it (as specifie in the [[Manual:IP/Address|<code>/ip address</c

...d a message to the system log containing following data: in-interface, out-interface, src-mac, protocol, src-ip:port->dst-ip:port and length of the packet. Afte <td><var><b>in-bridge-port</b></var> (<em>name</em>; Default: <b></b>)</td>

...d a message to the system log containing following data: in-interface, out-interface, src-mac, protocol, src-ip:port->dst-ip:port and length of the packet. Afte ...ink that is capable of transporting priority (VLAN or WMM-enabled wireless interface). [[WMM#How_to_set_priority | Read more>]]

...eshooting, here is little reminder on how to check host computer's network interface parameters on . ...assigned IP address and netmask details as well as show currently network interface configuration.

The PPPoE client and server work over any Layer2 Ethernet level interface on the router - wireless 802.11 (Aironet, Cisco, WaveLan, Prism, Atheros), * BCP (Bridge Control Protocol) support - allows sending of raw Ethernet frames over PPP

...er SSTP. Client authenticates to the server and binds IP addresses to SSTP interface ...g | RSA Key length must be at least 472 bits if certificate is used by [[M:Interface/SSTP | SSTP]]. Shorter keys are considered as security threats.}}

...ot]], PPP, [[M:Interface/PPPoE | PPPoE]], [[M:Interface/PPTP | PPTP]], [[M:Interface/L2TP | L2TP]] and ISDN connections. The attributes received from RADIUS ser ...b></var> - PPPoE - service name; PPTP and L2TP - server IP address; ISDN - interface MSN; HotSpot - name of the HotSpot server

...ess can operate in several modes: client (station), access point, wireless bridge etc. Client/station also can operate in different modes, complete list of s ==General interface properties==