Manual:Configuration Management

From CableFree RadioOS
Revision as of 16:46, 26 January 2015 by Administrator (talk | contribs) (→‎Example)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Applies to RadioOS: ALL


This manual introduces you with commands which are used to perform the following functions:

  • system backup;
  • system restore from a backup;
  • configuration export;
  • configuration import;
  • system configuration reset.


The configuration backup can be used for backing up CableFree RadioOS configuration to a binary file, which can be stored on the router or downloaded from it using FTP for future use. The configuration restore can be used for restoring the router's configuration, exactly as it was at the backup creation moment, from a backup file. The restoration procedure assumes the cofiguration is restored on the same router, where the backup file was originally created, so it will create partially broken configuration if the hardware has been changed.

The configuration export can be used for dumping out complete or partial CableFree RadioOS configuration to the console screen or to a text (script) file, which can be downloaded from the router using FTP protocol. The configuration dumped is actually a batch of commands that add (without removing the existing configuration) the selected configuration to a router. The configuration import facility executes a batch of console commands from a script file.

System reset command is used to erase all configuration on the router. Before doing that, it might be useful to backup the router's configuration.

System Backup

Submenu level: /system backup


The backup save command is used to store the entire router configuration in a backup file. The file is shown in the /file submenu. It can be downloaded via ftp to keep it as a backup for your configuration.

Important! The backup file contains sensitive information, do not store your backup files inside the router's Files directory, instead, download them, and keep them in a secure location.


Warning: If TheDude and user-manager is installed on the router then backup will not take care of configuration used by these tools. Therefore additional care should be taken to save configuration from these. Use provided tool mechanisms to save/export configuration if you want to save it.

To restore the system configuration, for example, after a /system reset-configuration, it is possible to upload that file via ftp and load that backup file using load command in /system backup submenu.

Since RadioOS v6.13 it is possible to encrypt the backup files with RC4.

Command Description

  • load name=[filename] - Load configuration backup from a file
  • save name=[filename] - Save configuration backup to a file (when no name is provided, default name will be used, and previous file will be overwritten)
  • dont-encrypt - tells the system to not use any encryption and make the file readable in text editors (DANGEROUS)
  • password - when not specified, current user password will be asked when restoring the file. when specified - this password will be asked instead.


Since RadioOS v6.13 the backup file is encrypted by default, if the current RadioOS user has a password configured, or if the "password" parameter is used. If your RadioOS user doesn't have a password set (for example admin and no password) then backup file is not encrypted, to enable encryption in this case, use the "password" parameter.

Notice that it is useless to set password, if you will use the "dont-encrypt=yes" parameter, the password can only be used with encrypted files.


To save the router configuration to file test:

[admin@CableFree] system backup> save name=test
Configuration backup saved
[admin@CableFree] system backup>

To see the files stored on the router:

[admin@CableFree] > file print
  # NAME                           TYPE         SIZE       CREATION-TIME
  0 test.backup                    backup       12567      sep/08/2004 21:07:50
[admin@CableFree] >

To load the saved backup file test:

[admin@CableFree] > system backup load name=test 
Restore and reboot? [y/N]: 
Restoring system configuration
System configuration restored, rebooting now

Exporting Configuration

Command name: /export

The export command prints a script that can be used to restore configuration. The command can be invoked at any menu level, and it acts for that menu level and all menu levels below it. The output can be saved into a file, available for download using FTP.

Command Description

  • file=[filename] - saves the export to a file


[admin@CableFree] > ip address print
Flags: X - disabled, I - invalid, D - dynamic
 #   ADDRESS            NETWORK         BROADCAST       INTERFACE
 0      bridge1
 1      ether1
[admin@CableFree] >

To make an export file:

[admin@CableFree] ip address> export file=address
[admin@CableFree] ip address>

To see the files stored on the router:

[admin@CableFree] > file print
 # NAME                            TYPE         SIZE       CREATION-TIME
0  address.rsc                     script       315        dec/23/2003 13:21:48
[admin@CableFree] >

Compact Export

Starting from v5.12 compact export was added. It allows to export only part of configuration that is not default RadioOS config.


Note: Starting from v6rc1 "export compact" is default behavior. To do old style export use export verbose

For example compact OSPF export:

[admin@CableFree] /routing ospf> export compact 
# jan/02/1970 20:16:32 by RadioOS 5.12
# software id = JRB7-9UGC
/routing ospf instance
set [ find default=yes ] redistribute-connected=as-type-1
/routing ospf interface
add disabled=yes interface=wlan1 network-type=point-to-point
/routing ospf network
add area=backbone network=
add area=backbone disabled=yes network=
add area=backbone network=
[admin@CableFree] /routing ospf> 

Compact export introduces another feature that indicates which part of config is default on RadioOS and cannot be deleted. As in example below '*' indicates that this OSPF instance is part of default configuration.

[admin@CableFree] /routing ospf instance> print 
Flags: X - disabled, * - default 
 0  * name="default" router-id= distribute-default=never 
      redistribute-connected=as-type-1 redistribute-static=no 
      redistribute-rip=no redistribute-bgp=no redistribute-other-ospf=no 
      metric-default=1 metric-connected=20 metric-static=20 metric-rip=20 
      metric-bgp=auto metric-other-ospf=auto in-filter=ospf-in 

List of default config by menus that cannot be removed:

Menu Entries
/interface wireless security-profiles default
/ppp profile "default", "default-encryption"
/ip hotspot profile "default"
/ip hotspot user profile "default"
/ip ipsec proposal "default"
/ip smb shares "pub"
/ip smb users "guest"
/ipv6 nd "all"
/mpls interface "all"
/routing bfd interface "all"
/routing bgp instance "default"
/routing ospf instance "default"
/routing ospf area "backbone"
/routing ospf-v3 instance "default"
/routing ospf-v3 area "backbone"
/snmp community "public"
/tool mac-server mac-winbox "all"
/tool mac-server "all"
/system logging "info", "error", "warning", "critical"
/system logging action "memory", "disk", "echo", "remote"
/queue type "default", "ethernet-default", "wireless-default", "synchronous-default", "hotspot-default", "only-hardware-queue", "multi-queue-ethernet-default", "default-small"

Importing Configuration

Command name: /import

The root level command /import [file_name] executes a script, stored in the specified file adds the configuration from the specified file to the existing setup. This file may contain any console comands, including scripts. is used to restore configuration or part of it after a /system reset event or anything that causes configuration data loss.

Command Description

  • file=[filename] - loads the exported configuration from a file to router

Automatic Import

Since RadioOS v3rc it is possible to automatically execute scripts - your script file has to be called - once this file is uploaded with FTP to the router, it will automatically be executed, just like with the Import command. This method only works with FTP.

Once the file is uploaded, commands in the file are executed, and the file is replaced by which contains information about the success of the commands that were executed.


To load the saved export file use the following command:

[admin@CableFree] > import address.rsc
Opening script file address.rsc

Script file loaded and executed successfully
[admin@CableFree] >

Configuration Reset

Command name: /system reset-configuration


The command clears all configuration of the router and sets it to the default including the login name and password ('admin' and no password), IP addresses and other configuration is erased, interfaces will become disabled. After the reset command router will reboot.

Command Description

  • keep-users: keeps router users and passwords
  • no-defaults: doesn't load any default cofigurations, just clears everything
  • skip-backup: automatic backup is not created before reset, when yes is specified
  • run-after-reset: specify export file name to run after reset

Warning: Warning: If device has "flash" directory, then confscript.rsc file must be placed in it to work with "run-after-reset" command. Cause everything outside this directory is in RAM drive which contents is deleted on reboot or power cycle.


Warning: If the router has been installed using netinstall and had a script specified as the initial configuration, the reset command executes this script after purging the configuration. To stop it doing so, you will have to reinstall the router.


[admin@CableFree] > system reset-configuration
Dangerous! Reset anyway? [y/N]: n
action cancelled
[admin@CableFree] >