Manual:Interface/VLAN

From CableFree RadioOS
Jump to navigation Jump to search
The printable version is no longer supported and may have rendering errors. Please update your browser bookmarks and please use the default browser print function instead.
Version.png

Applies to RadioOS: v3, v4+

Summary

Sub-menu: /interface vlan
Standards: IEEE 802.1Q

Virtual Local Area Network (VLAN) is a Layer 2 method that allows multiple Virtual LANs on a single physical interface (ethernet, wireless, etc.), giving the ability to segregate LANs efficiently.

You can use CableFree RadioOS (as well as Cisco IOS, Linux and other router systems) to mark these packets as well as to accept and route marked ones.

As VLAN works on OSI Layer 2, it can be used just as any other network interface without any restrictions. VLAN successfully passes through regular Ethernet bridges.

You can also transport VLANs over wireless links and put multiple VLAN interfaces on a single wireless interface. Note that as VLAN is not a full tunnel protocol (i.e., it does not have additional fields to transport MAC addresses of sender and recipient), the same limitation applies to bridging over VLAN as to bridging plain wireless interfaces. In other words, while wireless clients may participate in VLANs put on wireless interfaces, it is not possible to have VLAN put on a wireless interface in station mode bridged with any other interface.

802.1Q

The most commonly used protocol for Virtual LANs (VLANs) is IEEE 802.1Q. It is a standardized encapsulation protocol that defines how to insert a four-byte VLAN identifier into Ethernet header. (see Figure 12.1.)

Image12001.gif

Each VLAN is treated as a separate subnet. It means that by default, a host in a specific VLAN cannot communicate with a host that is a member of another VLAN, although they are connected in the same switch. So if you want inter-VLAN communication you need a router. RadioOS supports up to 4095 VLAN interfaces, each with a unique VLAN ID, per interface. VLAN priorities may also be used and manipulated.

When the VLAN extends over more than one switch, the inter-switch link has to become a 'trunk', where packets are tagged to indicate which VLAN they belong to. A trunk carries the traffic of multiple VLANs; it is like a point-to-point link that carries tagged packets between switches or between a switch and router.

Image12003.gif


Q-in-Q

Original 802.1Q allows only one vlan header, Q-in-Q on the other hand allows two or more vlan headers. In RadioOS Q-in-Q can be configured by adding one vlan interface over another. Example:

/interface vlan
add name=vlan1 vlan-id=11 interface=ether1
add name=vlan2 vlan-id=12 interface=vlan1

If any packet is sent over 'vlan2' interface, two vlan tags will be added to ethernet header - '11' and '12'.

Properties

Property Description
arp (disabled | enabled | proxy-arp | reply-only; Default: enabled) Address Resolution Protocol mode
interface (name; Default: ) Name of physical interface on top of which VLAN will work
l2mtu (integer; Default: ) Layer2 MTU. For VLANS this value is not configurable. Read more>>
mtu (integer; Default: 1500) Layer3 Maximum transmission unit
name (string; Default: ) Interface name
use-service-tag (yes | no; Default: ) 802.1ad compatible Service Tag
vlan-id (integer: 4095; Default: 1) Virtual LAN identifier or tag that is used to distinguish VLANs. Must be equal for all computers that belong to the same VLAN.


Icon-note.png

Note: MTU should be set to 1500 bytes same as on Ethernet interfaces. But this may not work with some Ethernet cards that do not support receiving/transmitting of full size Ethernet packets with VLAN header added (1500 bytes data + 4 bytes VLAN header + 14 bytes Ethernet header). In this situation MTU 1496 can be used, but note that this will cause packet fragmentation if larger packets have to be sent over interface. At the same time remember that MTU 1496 may cause problems if path MTU discovery is not working properly between source and destination.


Setup examples

Simple Example

Lets assume that we have several CableFree routers connected to a hub. Remember that a hub is an OSI physical layer device (if there is a hub between routers, then from L3 point of view it is the same as an Ethernet cable connection between them). For simplification assume that all routers are connected to the hub using ether1 interface and has assigned IP addresses as illustrated in figure below. Then on each of them the VLAN interface is created. Image12004.gif

Configuration for R2 and R4 is shown below:

R2:

[admin@CableFree] /interface vlan> add name=VLAN2 vlan-id=2 interface=ether1 disabled=no

[admin@CableFree] /interface vlan> print 
Flags: X - disabled, R - running, S - slave 
 #    NAME                  MTU   ARP        VLAN-ID INTERFACE                
0 R  VLAN2                 1500  enabled    2       ether1


R4:

[admin@CableFree] /interface vlan> add name=VLAN2 vlan-id=2 interface=ether1 disabled=no

[admin@CableFree] /interface vlan> print 
Flags: X - disabled, R - running, S - slave 
 #    NAME                  MTU   ARP        VLAN-ID INTERFACE                
0 R  VLAN2                 1500  enabled    2       ether1


The next step is to assign IP addresses to the VLAN interfaces.

R2:

 [admin@CableFree] ip address> add address=10.10.10.3/24 interface=VLAN2
 [admin@CableFree] ip address> print
 Flags: X - disabled, I - invalid, D - dynamic
   #   ADDRESS            NETWORK         BROADCAST       INTERFACE
   0   10.0.1.4/24        10.0.1.0        10.0.1.255      ether1
   1   10.20.0.1/24       10.20.0.0       10.20.0.255     pc1
   2   10.10.10.3/24      10.10.10.0      10.10.10.255    vlan2

 [admin@CableFree] ip address>

R4:

 [admin@CableFree] ip address> add address=10.10.10.5/24 interface=VLAN2
 [admin@CableFree] ip address> print
 Flags: X - disabled, I - invalid, D - dynamic
   #   ADDRESS            NETWORK         BROADCAST       INTERFACE
   0   10.0.1.5/24        10.0.1.0        10.0.1.255      ether1
   1   10.30.0.1/24       10.30.0.0       10.30.0.255     pc2
   2   10.10.10.5/24      10.10.10.0      10.10.10.255    vlan2

[admin@CableFree] ip address>


At this point it should be possible to ping router R4 from router R2 and vice versa:

 "Ping from R2 to R4:"

 [admin@CableFree] ip address> /ping 10.10.10.5

 10.10.10.5 64 byte ping: ttl=255 time=4 ms

 10.10.10.5 64 byte ping: ttl=255 time=1 ms

 2 packets transmitted, 2 packets received, 0% packet loss

 round-trip min/avg/max = 1/2.5/4 ms


 "From R4 to R2:"
 
 [admin@CableFree] ip address> /ping 10.10.10.3
 10.10.10.3 64 byte ping: ttl=255 time=6 ms
 10.10.10.3 64 byte ping: ttl=255 time=1 ms
 2 packets transmitted, 2 packets received, 0% packet loss
 round-trip min/avg/max = 1/3.5/6 ms

To make sure if VLAN setup is working properly, try to ping R1 from R2. If pings are timing out then VLANs are successfully isolated.

 
 "From R2 to R1:"

 [admin@CableFree] ip address> /ping 10.10.10.2
 10.10.10.2 ping timeout
 10.10.10.2 ping timeout
 3 packets transmitted, 0 packets received, 100% packet loss

Create 'trunks' and implement routing between VLANs

If separate VLANs are implemented on a switch, then a router is required to provide communication between VLANs. Switch works at OSI layer 2 so it uses only Ethernet header to forward and does not check IP header. For this reason we must use the router that is working as a gateway for each VLAN. Without a router, a host is unable to communicate outside of its own VLAN. Routing process between VLANs described above is called inter-VLAN communication.

To illustrate inter-VLAN communication, we will create a trunk that will carry traffic from three VLANs (VLAN2 and VLAN3, VLAN4) across a single link between a CableFree router and a manageable switch that supports VLAN trunking. Image12005.gif

Each VLAN has its own separate subnet (broadcast domain) as we see in figure above:

  • VLAN 2 – 10.10.20.0/24;
  • VLAN 3 – 10.10.30.0/24;
  • VLAN 4 – 10.10.40.0./24.

VLAN configuration on most switches is straightforward, basically we need to define which ports are members of the VLANs and define a 'trunk' port that can carry tagged frames between the switch and the router.

"Configuration example on CableFree router:"

"Create VLAN interfaces:"

/interface vlan
add name=VLAN2 vlan-id=2 interface=ether1 disabled=no
add name=VLAN3 vlan-id=3 interface=ether1 disabled=no
add name=VLAN4 vlan-id=4 interface=ether1 disabled=no

"Add IP addresses to VLANs:"

/ip address 
add address=10.10.20.1/24 interface=VLAN2
add address=10.10.30.1/24 interface=VLAN3
add address=10.10.40.1/24 interface=VLAN4

RadioOS /32 and IP unnumbered addresses

In RadioOS, to create a point-to-point tunnel with addresses you have to use address with a network mask of '/32' that effectively brings you the same features as some vendors unnumbered IP address.

There are 2 routers RouterA and RouterB where each is part of networks 10.22.0.0/24 and 10.23.0.0/24 respectively and to connect these routers using VLANs as a carrier with the following configuration:

Slash32.png

RouterA:

 /ip address add address=10.22.0.1/24 interface=ether1
 /interface vlan add interface=ether2 vlan-id=1 name=vlan1
 /ip address add address=10.22.0.1/32 interface=vlan1 network=10.23.0.1
 /ip route add gateway=10.23.0.1 dst-address=10.23.0.0/24

RouterB:

 /ip address add address=10.23.0.1/24 interface=ether1
 /interface vlan add interface=ether2 vlan-id=1 name=vlan1
 /ip address add address=10.23.0.1/32 interface=vlan1 network=10.22.0.1
 /ip route add gateway=10.22.0.1 dst-address=10.22.0.0/24


[ Top | Back to Content ]